Diy landscape lighting ideas

The installation process essentially comprises three steps — one for each of the three key components of the system.

Next You Install the Transformer

  1. However, make certain the electrical outlet you use to power the transformer is a ground-fault circuit interrupter (GFCI) outlet, as it will protect you from electrical shocks.
  2. Low-voltage cables are typically double stranded.
  3. You need to peel apart about inches of the two strands.
  4. Next, you own to use a wire cutter to remove an inch of the insulated cover off the top of each strand in order to expose the copper wire underneath.
  5. Slip both strands into the transformer via the slot at the back.
  6. You can repair the transformer on a wooden stake that’s been pressure treated (the ones generally used in fences).

    Diy landscape lighting ideas

    Alternatively, you can repair on an exterior wall, ideally a little distance away from the main house.

  7. Inside the transformer, you will discover two screw terminals marked ‘A’ and ‘B’. You own to slide one exposed finish of the copper wire into each of the terminals and tighten the screw to secure its position.
  8. Once the light fixtures own been connected and tested (which has been elaborated in the next section), you will own to cover the transformer with a weatherproof cover.

First You Own to Lay the Cable

  1. Now put the cable in the trench and press it below into the ground.

    Don’t use the shovel to press the cable, as that might damage the cable.

  2. Begin by placing the light fixtures in the positions where you own decided to install them.
  3. Take the spool of cable and lay it beside the light fixtures, every the way till where the transformer will be installed.
  4. If you come across an obstacle while laying the cable, love a tree or part of the fence, then just either slip the cable under the obstacle or around it.
  5. After laying the cable till the transformer’s location, use a shovel to dig a shallow trench (about 3 inches deep) along the line of the cable that’s been laid out. Just love in case of the cable, if you meet an obstacle then dig the trench around it.
  6. You will own to cover up the trench with the soil that you’ve dug up and then tap on it with your boot to pack in it tightly.

    However, you do this at the extremely finish, when the transformer has been installed and the light fixtures own been connected. This will save you some time in case you need to make any final minute changes.

Finally, You Join the Light Fixtures

  1. Next, you cover up the cable as mentioned earlier.
  2. Generally, landscaping light fixtures are equipped with what’s known as snap-on connectors.
  3. These connectors enable you to simply snap the prewired prongs onto the cable.

    Diy landscape lighting ideas

    The prongs bite into the cable and come in contact with the copper wire underneath.

  4. However, even though the connectors are super convenient, they aren’t ideal. The reason being that the wire remains partly exposed and could be affected by water or other elements.
  5. You need to cut off the connectors, expose about half an inch of the wire from under the insulated cover and install weatherproof wire connectors, which own a sealant and base shield.
  6. When you’re satisfied that every the light fixtures are working fine, you own to install them as required.

    So, if it’s a well light you must own hole dug deep enough for it to sit comfortably. For path lights you will own to stick them into the ground deep enough to ensure they are stable.

  7. Once this is done, switch on the transformer and test each and every light fixture.
  8. Finally, you need to set the transformer timer and select the switch on and switch off times for the lights.

We hope these tips come in handy when you’re every set to light up your landscape area.

Hold these tips in mind and you’ll a wonderfully lit outdoor space!

Comments will be approved before showing up.

Outdoor living before the sun goes below is lovely. But add a little landscape lighting and moonlight to the stir and youve got an enchanting backdrop for every your exterior celebrations!

If youd love to add some DIY landscape lighting to your outdoor living area, Id love to show you how we did ours!



Adding DIY Landscaping Lights

First, decide on a plan- Consider what youd love to accent.

Some questions to get you started

  • Do you desire a light mounted in a tree shining below onto a specific area?

    (These give a moonlight effect and are so pretty when shining onto a garden area.)

  • What part of  your yard, flower beds, water features or trees would you love illuminated?
  • Do you own a space (eating area, fire pit) that would benefit from string lights?

We decided to uplight a few trees and add lighting to the garden area surrounding our water feature. We also added a giant criss-cross of string lights over the fire pit.

Lets start with the up-lights

Step 8

Plug the power pack into power source and set automatic timer according to instructions.


Step 1

Assemble the lights according to the directions.


Materials for this DIY Landscaping Light Project


Step 2

Place the lights in the locations that youve chosen in your plan.


Step 4

Take one finish of your wire and lay it at the farthest light from the power pack.

Now, lay the wire from light to light until you make your way to the power pack-dont tug the wire tight. (Keep in mind youll desire to bury or cover the wire later, so hold the wire in pine/mulch islands or around the perimeter of your lawn.)


Step 6

Connect the wires at each light location according to your instructions.


Step 5

Connect wire to the power pack by taking the power pack off the wall

Using wire strippers, strip the wires as shown.

Attach the stripped wires to the terminals on the back of the power pack.

 Now put your power pack back on the wall.

DO NOT PLUG POWER PACK INTO POWER SOURCE YET.


Step 3

Find an outdoor electrical outlet shut to the space youre working on, and mount the power pack shut to the outlet.

We used cement  anchors  for brick, but you can use wood screws for mounting to the side of your house.

DO NOT PLUG POWER PACK INTO POWER SOURCE YET.


Step 7

Stick your lights back into the ground!


Step 9

Go back through your yard and cover the electrical wire with pine straw or mulch if its located in a bed, or you can dig a  shallow trench to bury the wire.

Once your lights are working, wait till dusk and make certain your lights are pointing in the correct direction.

Adjust as necessary!


We decided to uplight a few trees and add lighting to the garden area surrounding our water feature. We also added a giant criss-cross of string lights over the fire pit.

Lets start with the up-lights

Step 8

Plug the power pack into power source and set automatic timer according to instructions.


Step 1

Assemble the lights according to the directions.


Materials for this DIY Landscaping Light Project


Step 2

Place the lights in the locations that youve chosen in your plan.


Step 4

Take one finish of your wire and lay it at the farthest light from the power pack.

Now, lay the wire from light to light until you make your way to the power pack-dont tug the wire tight. (Keep in mind youll desire to bury or cover the wire later, so hold the wire in pine/mulch islands or around the perimeter of your lawn.)


Step 6

Connect the wires at each light location according to your instructions.


Step 5

Connect wire to the power pack by taking the power pack off the wall

Using wire strippers, strip the wires as shown.

Attach the stripped wires to the terminals on the back of the power pack.

 Now put your power pack back on the wall.

DO NOT PLUG POWER PACK INTO POWER SOURCE YET.


Step 3

Find an outdoor electrical outlet shut to the space youre working on, and mount the power pack shut to the outlet.

We used cement  anchors  for brick, but you can use wood screws for mounting to the side of your house.

DO NOT PLUG POWER PACK INTO POWER SOURCE YET.


Step 7

Stick your lights back into the ground!


Step 9

Go back through your yard and cover the electrical wire with pine straw or mulch if its located in a bed, or you can dig a  shallow trench to bury the wire.

Once your lights are working, wait till dusk and make certain your lights are pointing in the correct direction.

Adjust as necessary!



The Key Components of a Low-Voltage Landscape Lighting Setup

Light Fixture

There’s a plethora of light fixtures available in various price ranges. Selecting the correct collection of light fixtures is significant, because they will ultimately be responsible for the aesthetics. Hence, you need to first chalk out a clear plan and make a list of the types of light fixtures you require.

Diy landscape lighting ideas

One way of doing this is asking yourself a few simple questions.

  1. Well light
  2. Do I desire to light only the pathways or the features around them as well? If you desire the field of the light to be broader than just the pathway, then you would require higher light poles and possibly cone lights. If you desire the light to focus only on the pathway, then you could opt for offset path lights.
  3. Is there a pond or sprinklers in the garden? If yes, then the light fixtures to be placed near the pond and in the arc of the sprinklers need to be waterproof.
  4. Does every part of the outdoor space need to be lit or should the lights only accentuate the space?

    If you prefer the latter option, then you won’t own to purchase powerful halogen lights.

  5. Path light
  6. Wall wash light
  7. Spot light
  8. Flood light
  9. Submersible pond light

Basic Light Fixtures

  • Well light
  • Flood light
  • Path light
  • Spot light
  • Wall wash light
  • Submersible pond light

You can get path lights in a variety of styles and in packs of 2, 4, 6, 8 and You can also get finish kits, including flood lights, path lights, spot lights and a transformer.

Every light fixtures are available with LEDs, which is the ideal option for residential landscape lighting.

Now that you own a better thought about the types of light fixtures suited for the outdoor space around your home, you also need to take into consideration their longevity. A light fixture in a plastic casing won’t final as endless as one with a metal casing. Obviously, the the metal fixtures will cost more, but will eventually balance itself because of its longevity.

Finally, remember that it’s your space and you should let your imagination guide you.

Transformer

The transformer is the most significant element in the low-voltage lighting system.

It steps below the standard volt current is household to 12 volt for the landscape lighting system. Ideally, you should purchase a transformer that has a hour timer, allowing you to set a specific time for the lights to be automatically switched on and off.

The other thing you need to hold in mind is to purchase a transformer with a power output slightly higher than what you need at the time of setting up the landscape lighting system. For example, if the entire wattage of the light fixtures you plan to install comes up to watt, then purchase a watt transformer. This will enable you to add to your lighting system later on, without having to invest in a new transformer.

Low-Voltage Electrical Cable

The cable connects the light fixtures to the transformers.

Generally, the gauge, gauge and gauge cables are used for residential landscape lighting. Note that the gauge cable is thicker than the gauge cable and has greater current delivery capacity. Similarly, the gauge cableis thicker than the gauge cable and equipped to handle more current.

For example, if your transformer is watts, then in case of the gauge cable, it can power only feet, for the gauge cable it can power feet and for gauge cable it can power feet. So, you need to calculate the entire length of cable required to join every the light fixtures and then select the correct gauge of cable you need to purchase, keeping in mind the transformer wattage.

One more thing.

Since, you will own to bury the cable, you should get in touch with the utilities company and enquire them to mark out the locations of the cables and pipelines under your property. This will ensure that you accidentally don’t damage one of them.

You can get path lights in a variety of styles and in packs of 2, 4, 6, 8 and You can also get finish kits, including flood lights, path lights, spot lights and a transformer.

Every light fixtures are available with LEDs, which is the ideal option for residential landscape lighting.

Now that you own a better thought about the types of light fixtures suited for the outdoor space around your home, you also need to take into consideration their longevity. A light fixture in a plastic casing won’t final as endless as one with a metal casing. Obviously, the the metal fixtures will cost more, but will eventually balance itself because of its longevity.

Finally, remember that it’s your space and you should let your imagination guide you.

Transformer

The transformer is the most significant element in the low-voltage lighting system.

It steps below the standard volt current is household to 12 volt for the landscape lighting system. Ideally, you should purchase a transformer that has a hour timer, allowing you to set a specific time for the lights to be automatically switched on and off.

The other thing you need to hold in mind is to purchase a transformer with a power output slightly higher than what you need at the time of setting up the landscape lighting system. For example, if the entire wattage of the light fixtures you plan to install comes up to watt, then purchase a watt transformer.

This will enable you to add to your lighting system later on, without having to invest in a new transformer.

Low-Voltage Electrical Cable

The cable connects the light fixtures to the transformers. Generally, the gauge, gauge and gauge cables are used for residential landscape lighting. Note that the gauge cable is thicker than the gauge cable and has greater current delivery capacity. Similarly, the gauge cableis thicker than the gauge cable and equipped to handle more current.

For example, if your transformer is watts, then in case of the gauge cable, it can power only feet, for the gauge cable it can power feet and for gauge cable it can power feet.

So, you need to calculate the entire length of cable required to join every the light fixtures and then select the correct gauge of cable you need to purchase, keeping in mind the transformer wattage.

One more thing. Since, you will own to bury the cable, you should get in touch with the utilities company and enquire them to mark out the locations of the cables and pipelines under your property. This will ensure that you accidentally don’t damage one of them.


Adding String Lights

Now for another layer of ambiance using string lights!

Step 2

Take the other finish of the cable to the corresponding tree or pole youre using to attach your lights.

Extend the turn buckle by spinning the middle and run the cable through the eye.

Put the wire rope clip on the cable but dont tighten.

Attach the hook finish of the turn buckle to the eye you put in the tree or pole, then tug the slack out of the cable to tighten. Secure the wire rope clip.

The turn buckle can now be adjusted to tighten the entire length of the cable. (Ours was 70 feet, so we needed additional tension to hold the lights from sagging in the center.)


Materials needed to add string lights

If you havent done so already, nows the time to decide where you desire your string lights.

Also consider exactly where youll attach them.

Diy landscape lighting ideas

We decided to attach ours onto our decking and a few trees, creating a  criss-cross pattern over the fire pit and waterfall.

If you dont own trees or decking available, you could easily install poles or for a temporary solutionlike maybe if youll be throwing a bunch of parties this summer, you could put poles into weighted buckets!


Step 1

When you decide on where and how youll hang your lights, add screw eyes and join the cable to the eye.

Secure with the wire rope clip.

Tighten the nuts.


Step 3

Now its time to hang your lights!

Plug the first set of string lights into your extension cord to test and start hanging the lights on the cable with zip ties.

Continue to join your lights and hang them with the zip ties. Remember,  dont join more than the recommended number of strings.

I love them even in the daylight, but when the sun starts to go down

these little string lights

 add a whole lot of atmosphere!

Adding another simple layer of outdoor lighting can be enjoyment, love these beautiful lanterns from Home Depot.

(When you use a battery operated candle, the candle can be set to come on at the same time your landscape lights flicker on!)

Its simple to give your outdoor space a soft inviting glow that will hold you spending your nights under the stars correct up until that first freeze!

Browse The Home Depots Outdoor Lighting Department for everything you need to install landscape lighting.

Theres nothing better for adding an elegant, magical ambiance to your backyard or deck than outdoor lighting.

Its grand, too, for enhancing curb appeal in the front of your home. Landscape lighting increases your home security, too.

Installing your own DIY landscape lighting is beautiful simple, too. DIY blogger Robin Gay of All Things Heart and Home has done some beautiful amazing things with outdoor lighting in her yard. Here she shows up how to set up a DIY  outdoor lighting system.

Everyone wants their patio or lawn to glance its absolute best without spending a fortune, doing an huge overhaul of the existing layout, or fixing what’s not broken—and we know that.

Diy landscape lighting ideas

That’s why we’ve compiled a list of the absolute best backyard ideas out there. We’re coming to your save with plenty of beautiful projects, inspired suggestions, and brilliant hacks that you can implement quickly and while on a budget. Instead of doling out dough on a professional designer who will charge a fortune for your wildest and most amazing landscape ideas, save money and take matters into your own hands. You can either skim through our list and get ideas from the eye candy you discover there, or dig a little deeper and study how to recreate each of the looks you see here.

So, what exactly will you discover on our list?

Well, a little bit of everything—from porch and patio decorating ideas to DIY fire pits and never-before-seen planters. In fact, each and every one of these innovative, out-of-the-box tutorials is guaranteed to work for large and little backyards. Yes, we’re really telling you that you can create the backyard of your dreams without breaking the bank—and we’ll stand by our expression. Now, let’s get building!

You also need a transformer or two to step below the Volts coming from your home to 12 Volts for your outdoor fixtures, feet or more of landscape wire, and a square-blade shovel. When choosing a transformer, it’s significant to pick one that can handle the entire wattage of your fixtures.

For example, if you add up the wattages of every your fixtures for a entire of Watts then you at least need a transformer with a maximum output of Watts. If you ponder you might add more lights in the future then select a transformer with a max wattage that’s to Watts higher than the current entire wattage of your fixtures. While LEDs are becoming a more favorite choice for this helpful of project, if you decide to go with traditional halogen lighting then you will to need purchase a transformer with a maximum wattage of 20% more than your entire wattage. That means the transformer should never be loaded with more than 80% capacity of its rated max wattage. This is called derating and helps to account for inefficiencies in the transformers.

Low voltage landscape wiring or electrical cable comes in several numerical gauges or sizes.

A lower number means thicker wire and greater capacity to carry the power current for longer distances. Common wires for landscape lighting are , , , or gauge wires. We recommend gauge or gauge wire for endless distances. This is to prevent voltage drop. The further you get from the transformer and its power supply, the more resistance occurs in the circuit which causes the voltage to decrease.

Lighting Tip: You can run gauge about feet without voltage drop issues as endless as the entire wattage of the fixtures on the wire is Watts or less.


Advantages of Low Voltage Landscape Lighting

Cost Effective

You will own to purchase a transformer for a low-voltage setup, which isn’t required for the line voltage system. While the cables you would need for line voltage lighting are more expensive than those needed for low-voltage lighting. In addition, you should be using LED light fixtures in the low voltage system, which cost more than incandescent lights but final significantly longer. LED light fixtures also consume much less power, so your electricity bill will be lower as well.

Even if you don’t use LED fixtures, in a line voltage system you would require bulbs and fixtures that are 50 watts or more.

Whereas in a low voltage system, you can use bulbs and fixtures as low as watts.

Safe

This is probably the most significant reason why low-voltage landscape lighting is recommended for residential properties. You will obviously be spending some time in the outdoor space. It’s likely that you own kids at home, who will be playing in this space. Then there are your guests. A low-voltage lighting system with 12 volt power ensures that they will be protected from shocks, in case they mistakenly touch something. On the other hand, if you opt for line voltage, which has volt power, the consequences of an accident will be severe.

Ease of Installation

Setting up a line voltage landscape lighting system requires several safety measures such as burying the wires at least 18 feet deep and ensuring that the wire connections can be accessed via junction boxes.

So, it’s advisable that you hire a professional to oversee the entire process. In case of low voltage landscape lighting, you can set it up on your own. It’s essentially a transformer-cable-light fixtures setup, which is relatively simple to study. Plus, working in a low voltage setup is safe, so you can afford to do it yourself.

Aesthetics

Since, low-voltage landscape lighting has become the de facto choice for residential properties, manufacturers own developed a significantly wider variety of light fixtures for low-voltage systems.

Diy landscape lighting ideas

In terms of color and the lenses, there are numerous more options in a low-voltage system as compared to a line voltage system. This allows you to be more creative in designing the effect of the lights. You can move away from the garish halogen flood lights and create a more intricate lighting system.


RELATED VIDEO: